solar power garden signal LED Plastic road stud

Round solar power garden signal LED Plastic road stud
1. Product parameters of round solar road studs:
1. Product model: WDM-DD06-C-10R
2. Product size: 120*120MM
3. Color of lamp beads: red, yellow, blue, green and white
4. Number of lamp beads: 10
5. Red wavelength: 620-625NM
6. Yellow wavelength: 590-595NM
7. Blue wavelength: 470-475NM
8. Green wavelength: 520-525NM
9. White brightness: 18900-22600MCD
10. Protection grade: IP68
11. Shell material: plastic
12. Battery voltage: 1.2V
13. Solar panel: 2.5V
14. Working temperature: -40℃~60℃

15. Working mode: light control (often flashing / always on)

Features of round solar power garden signal LED Plastic road stud:
1. Round solar road studs are mainly used for Fishing boats, docks, villas, residential quarters, and garden courtyards as landscape lights. They outline the road and have a variety of uses.
2. The round solar spikes use 0.25W/2V monocrystalline silicon solar panels. Monocrystalline silicon is a relatively active non-metallic element. In addition to its general characteristics, it also has the advantages of high purity and high solar energy conversion rate.
3. The solar panel of the round solar spike is embedded in the PC frame, so that it can absorb solar energy better and will not be damaged by rolling.
4. The round solar road studs use ultra-bright Taiwan wafer chip lamp beads. The color is eye-catching and the color is clear. It has good visual performance during the day and night, which can attract the attention of the driver and reduce the speed of the car. To improve driving safety on highways.
5. Round solar road studs are available in a variety of colors, and the color of the lamp beads can be customized according to customer requirements.
6. The round solar road stud has the protection function of overcharge and over discharge.

7. The round solar road stud has good waterproof and dustproof effect, and the protection grade can reach IP68.

Installation steps of round solar power garden signal LED Plastic road stud
1. Installation instructions:
Roadside line (not recommended to be installed in the middle of the road, to avoid excessive impact of the car and damage to the spike)
2. Installation steps:
1> Positioning: first determine the installation position with a ruler to ensure that each position is on a straight line, the installation distance and the design requirements are subject to, the installation place should be flat, dry, clean and seamless.
2> Mixing glue: A glue for road studs, B glue for road studs, the ratio of A glue and B glue is 1:1 (for example: A glue 1 kg, B glue is 1 kg). The glue must be stirred evenly and the color should be the same.
3> Glue: The road surface should be cleaned during installation, and the glue should be moderate. Both the bottom surface of the road studs should be adhered to, and the overflow should not be too much. About 40-50 grams of glue should be used for each road stud, and the glue should be applied to the bottom surface of the road signs. Place on the pre-marked location. After installation, clear road debris.
4> Patrol: After two hours, the installed spikes should be checked again.

5> Road closure: It is recommended to close the road for 6 hours to ensure the curing time of the glue.

In addition to solar plastic round road studs, Vimee also produces Other solar transportation products
1. Solar strobe light
2. Solar yellow flashing light
3. Solar sign

4. Double-sided 4-lamp solar road studs, etc.

Contact us if you need more details on Plastic Road Stud. We are ready to answer your questions on packaging, logistics, certification or any other aspects about LED Plastic Road Stud、Garden Road Stud. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Road Stud > Plastic Road Stud